My amplifier project is complete! (I think)

Let your stereophile run loose! Talk gear, media, and other electronics that makes music for your ears.

Moderators: Bookworm, starkruzr, MrFireDragon, PrettyPrincess, Wapsi

Post Reply
User avatar
Posts: 7537
Joined: Tue Jul 31, 2012 5:58 pm
Location: Mountain View, CA, USA

My amplifier project is complete! (I think)

Post by Dave »

About five years ago, I decided I wanted to build an audio amplifier. I just finished the job.

pxl_20221214_200650828_jpg.jpeg (103.53 KiB) Viewed 1976 times

Years ago, I built a custom set of loudspeakers for our living room. They're a bit unusual, in that they are bi-amplified - one amplifier channel for the midrange and tweeter, another for the (sub)woofer, and an active "line-level" crossover feeding the amplifiers. They're also 4-ohm systems, which makes them a bit more difficult loads for the amplifiers than the usual 8-ohm systems would be. Over the years I've used several different pairs of stereo amps (all used ones) and have occasionally struggled with heat and reliability issues. I have long wanted to have an amplifier designed specifically for these speakers' needs. I decided to design and build one myself (rushing in where angels fear to tread).

My design goals included:
  • One amplifier chassis to drive both loudspeakers - hence, four channels of amplification. I decided to make them identical.
  • Low distortion, flat frequency response.
  • Optimized for driving 4-ohm speakers. This means "lower voltage, higher current" compared to an amp designed mostly for 8-ohm speakers.
  • Adequate but not brutal amounts of power - enough not to "clip" at sane listening levels, with plenty of headroom left for peaks.
  • Well-protected, with circuitry to protect both the amplifier (short-circuit and overload protection) and the speakers (DC-offset detection and shutdown).
  • Polite in use - no thumps when switched on or off, no big fuse-popping power surge when turned on.
  • Stable against oscillation (plenty of phase margin) even into difficult speaker loads.
  • Cool-running (which helps it be long-lived).
  • Something I can build mostly myself - no pre-built amplifier modules. I have enough Shopsmith and hand tools to fabricate things like component mountings, but a good case and proper heatsinks were things I knew I'd have to purchase.
I didn't have to start from scratch - rather, I read and took ideas from books and web sites by several very skilled amplifier designers (Doug Self, Bob Cordell, and Rod Elliot). Couldn't have done it without them.

The overall design is a classic Class B three-stage audio amp - differential input pair, voltage-amplification stage, and output section, all using bipolar transistors throughout. My first inspiration was Elliot's straightforward "Project 3A", which I then augmented with many of the distortion-reducing techniques in Self's "Blameless" amplifier designs.

I doubled up the output transistors (using the beefy On Semiconductor parts recommended by Elliot), assuring plenty of current drive into 4-ohm loads and plenty of "please don't burn up!" thermal margin. I added a standard "safe operating area" limiter to the drive circuit to protect the output transistors against accidental short-circuiting of the speaker wires. I put each channel onto an individual circuit board, with the boards being designed to fit into one of the "DIYAudio Store" heatsink-and-case kits.

The power sequencing, muting-relay control, DC offset detection/protection, and LED control are all handled by a small control board attached to the front panel. It's essentially a special-purpose Arduino design. Input jacks are decent-quality gold-plated RCA, output jacks are professional-style four-conductor SpeakOn twist-to-lock types from Neutrik.

I did all of the circuit design, SPICE simulation, and PC-board layout in the open-source KiCAD package.

There are three different custom PC boards - the amplifiers, the control board, and the special MOSFET solid-state muting relays. The amp and control boards were made by JLCPCB in China, the muting-relay boards by OSHPark here in the US. These sorts of PC-board service are so good, so inexpensive, and so convenient that I doubt I'll ever try to etch my own boards again... it's just too much trouble. Once I got the bare boards back from the manufacturer it was a matter of a few evenings' work to stuff and solder the parts.

p1790463_jpg.jpeg (145.09 KiB) Viewed 1976 times

I built and tested the amplifier boards during the weekends, a couple of years ago while we were stuck at home during the early stages of the COVID-19 lockdowns. Bringing up the boards was a fun experience. I built them in stages, starting with the input section, and working towards the output. With the addition of a temporary jumper or two, I could test the input and voltage-amplification stages, then install the output drivers and test them, and then finally install the final power transistors and heatsink and test the whole thing.

img_20200511_215918_jpg.jpeg (116.68 KiB) Viewed 1976 times
img_20200511_215922_jpg.jpeg (118.73 KiB) Viewed 1976 times

Both the amp boards and the control board went through two iterations, as I found issues in the prototypes which justified "re-spinning" the boards before I made the full set. The amplifier prototype board uses a combination of surface-mount and through-hole parts (my first real experiments with surface-mount). After building and debugging the prototype, I decided to switch back to all through-hole parts for the production boards, for ease and security of soldering (I'm not that good at SMT, and my home-brew toaster-oven reflow soldering setup isn't all that great).

I still have the prototype of the amp board sitting around - it might end up in a subwoofer cabinet one of these days.

The power supply uses a honkin'-big 24 VAC toroid transformer. The filtered DC is around 30-31 volts under full load. The system's central grounding point is a big slab of copper, which also serves as a heatsink for the bridge rectifier.

pxl_20220825_194843000_jpg.jpeg (140.03 KiB) Viewed 1976 times

I did most of the actual assembly work over the past nine months, post-retirement.

pxl_20221104_225847490_jpg.jpeg (175.09 KiB) Viewed 1976 times

I finished up the last of the testing shortly before Christmas, and finally hooked them up to the living-room system this afternoon. I'm a happy camper.
  • Maximum output signal is around 19.5 volts RMS, or 55 volts peak-to-peak.
  • Delivers about 48 watts/channel into three 8-ohm loads, plus about 80 watts into a 5-ohm load at the same time. At this full-power level the heatsinks are "happy kitty warm" after 30 minutes, but no worse than that.
  • After running the old FTC worst-case thermal load (1/3 full power for 30 minutes) the heatsinks are hot, but still comfortable to touch. I don't expect it's ever going to need a fan.
  • Should give at least 90 watts/channel into 4-ohm loads with all channels driven (I can't actually test this as I don't have enough high-power 4-ohm resistors).
  • At a normal "recreational listening" power level (1-2 watts per channel) the heatsinks are barely above room temperature.
  • Frequency response is flat down to about 5 Hz, and is a fraction of 1 dB down at 20 kHz.
  • At maximum power, total harmonic distortion at 1 kHz is under .01% into 4- and 8-ohm loads.
  • 1 kHz square wave looks beautiful - no ringing or instability.
  • The amp is completely stable driving reactive test load (8 ohms in parallel with 2 uF).
  • Hum and noise is below audibility if my ear is more than 6" from the speaker I tested it with.
  • The speaker-protection circuit will allow the amp to pass a full-power sine or square wave down to about 10 Hz, then begins to flash a warning. At 6-7 Hz it mutes the amp, and (if the signal continues) will turn off the main power.
  • The safe-operating-area circuit will allow for full-power output into loads as low as 2 ohms (even reactive ones). The output transistors are still well away from their safety limits (current and heat) at this point. If the impedance drops lower (e.g. a short circuit in the cable), the safety circuit limits the output voltage as necessary to keep the transistors from burning up.
I ran a "torture test" of the amp's ability to reproduce square waves, when driving a difficult (reactive) load such as the sorta-industry-standard "8 ohms, in parallel with 2 microfarads". The results are good - the blue trace shows the output of the amplifier board itself, and there's no sign at all of instability. The yellow trace shows the signal at the load. The ringing is caused by the capacitance, resonating with the inductance of the output-stabilization network (the big brown wire coils in the back of the amp in the picture above). Without proper stabilization, a capacitive load like this can cause an amplifier to break into a nasty oscillation which can actually destroy the amp - there's no trace of oscillation here.

2uf..8ohms.png (15.24 KiB) Viewed 1976 times

How do they sound? Fine - just like the two amps they replaced. I didn't really expect to hear any difference.

My next project is going to be to measure the whole system's frequency response and dispersion using the REW software and a good microphone, and see if some adjustment of the speaker crossovers is called for.

It's been a long project, which "went dormant" for months at a time while I worked on other things. My notes date back to January of 2018, so I guess it's almost exactly five years since I started working on it actively... and it's finally done.
User avatar
Sgt. Howard
Posts: 3316
Joined: Tue Jul 31, 2012 11:54 pm
Location: Malott, Washington

Re: My amplifier project is complete! (I think)

Post by Sgt. Howard »

Rule 17 of the Bombay Golf Course- "You shall play the ball where the monkey drops it,"
I speak fluent Limrick-
the Old Sgt.
User avatar
Posts: 2948
Joined: Tue Jul 31, 2012 12:39 am
Location: Central PA

Re: My amplifier project is complete! (I think)

Post by Atomic »

"Too many parts!" - Emperor Joseph II (Mozart)
Don't let other peoples limitations become your constraints!

My Deviant Art scribbles
The Atomic Guide to Basic GIMP Stuff
User avatar
Just Old Al
Posts: 1658
Joined: Tue Jul 31, 2012 4:43 am
Location: Wilderness of Massachusetts

Re: My amplifier project is complete! (I think)

Post by Just Old Al »

A stupid question - these are all plated-through boards, of course? You didn't need to solder both sides and innumerable feedthroughs....
"The Empire was founded on cups of tea, mate, and if you think I am going to war without one you are sadly mistaken."
User avatar
Posts: 7537
Joined: Tue Jul 31, 2012 5:58 pm
Location: Mountain View, CA, USA

Re: My amplifier project is complete! (I think)

Post by Dave »


These days, it's almost stupidity easy to order commercial-grade printed circuit boards with plated-through holes and vias, solder mask, and silkscreen. The issue you mention - not having to carefully solder components leads to the traces on both sides of the board - really makes commerical boards worth the small amount of money they cost. I don't see myself doing the expose-and-etch type of board at home again.

The four main amplifier boards are two-layer, with extra-thick copper plating (added a few dollars and a few days of processing to the order).

I did the initial layout of the controller board as a two-layer design, but it ended up needing more vias than I liked because a lot of the components are surface-mount. It turned out that changing it to a four-layer board simplified the routing a lot and let me use complete ground and power planes. The extra cost was only a couple of dollars per board - a big change from a few years ago.
Post Reply