A couple of members of our local amateur-radio e-comms group recently decided to sell their home and move to a retirement community in Oregon. As they're downsizing their living space, they had quite a few things they didn't care to take with them, and donated some of their used electronics gear to our repeater group for sale to help fund the repeater. They gave our senior guy the right to a "first pick" of anything he wanted for himself.
One thing he found was a McIntosh MA-5100 stereo preamp/amp, a 45 watt/channel beast built back around 1970. He was warned that it wasn't working... instead of making music, one channel was making 45 volts of DC, and would "burn up" any speaker it was connected to. This is usually a sign of a shorted output transistor... and the power transistors from that era were a bit fragile. He figured it wasn't worth more than about $20 as a flea-market sale item in its current condition, didn't have time to diagnose and repair it himself, and spent some time persuading me that I might find it a fun challenge. Eventually I caved in and agreed to give it a look.
This particular "Mac" was one of their first solid-state amplifiers. By today's standards it's of a somewhat primitive design (pseudo-complementary NPN output stage) with distortion specs that are nothing special, and a reputation for being a bit "hissy"... but there are a lot of people who seem to feel that it's actually one of the sweetest-sounding amplifiers of its era. They sold for $450 when new, and working units are selling on eBay for just about that price today (smaller dollars, of course). It's the sort of amp I could only have dreamed about owning back then (I was just about to enter college, and my whole first stereo cost only a fraction of what this thing sold for).
It's beautifully built - my friend describes it as resembling some of the military/aerospace electronics he was designing back around then - robust metal chassis, heavy transformer, big filter caps, two big heat-sinks in a protective cage, all through-hole components on several PC boards (easy to work on) and beautifully routed-and-laced point-to-point wiring. It has not one, but two "phono" inputs (even a single phono input is rare in preamps these days), and unlike a lot of older preamps it can handle the high signal voltage from a CD player without distorting. The cabinet has what appears to be genuine high-quality hardwood veneer - I could swear they actually used a "bookend" set of veneer on one end to create a pleasing grain pattern. Neither of us could face the thought of sending to to a dumpster or seeing it sold for parts, if it was salvageable. So, I took the schematic and dug in.
Fortunately, our first guess was wrong - the output transistors were still OK (if they short out, the stress tends to damage several "upstream" transistors and other components as well). After powering the amp up partway and comparing voltage levels on the two channels' boards, I found an "impossible" voltage level and identified the bad component - one of the bad board's transistors in the input/feedback differential pair had failed "open", and this caused a "go positive all the way" fault.
The original transistor types are mostly unavailable today, but properly-selected modern replacements are usually superior. I decided to give the amp a real "refresh" while I was working at it, to make it reliable enough for more years of good service, and replaced:
- Both differential transistor pairs (matched up two good pairs from a bag of JAN-rated 2N2907A I had)
- All four NPN output transistors. McIntosh has been replacing the original ones with MJ15003, which are quite a bit more rugged and reliable than the originals; I found some at a local dealer and was able to match up two good pairs.
- All six of the line-stage transistors. Both channels had a significant amount of hiss when the volume control was turned up partway - enough to be annoying, and I didn't like the way that it tended to appear and disappear. I found that McIntosh hadn't actually built this amp with the transistors specified in the schematic and parts list - they'd substituted something else - so I didn't feel bad about making substitutions of my own. I replaced the low-voltage transistors with 2N4401 (low noise) and the high-voltage amp with MPSA06 (also quite respectable noise performance). Voila - the hiss is almost entirely gone.
- All of the medium-sized electrolytic caps in the bias networks with modern "high temperature rated" parts.
- All of the front-panel lamp bulbs. Thought about replacing them with LEDs, but it would have been a lot of trouble and would probably have changed the classic appearance.
I carefully powered it up, ran it into some dummy-load resistors for a while, and adjusted the output-stage bias current to McIntosh's specifications.
The results: well, it work again now, and works quite nicely. It drives my little set of spare "bookshelf" speakers perfectly, although they aren't good enough to really evaluate its sound quality properly. With a set of good headphones, it sounds really sweet. It can heat up the "dummy load" resistors quite nicely, without its own output transistors and heat-sinks becoming more than very slightly warm to the touch. Two weekends of spare time, and about $30 - well spent!
I'm not sure where this is going to end up... neither my friend nor I have a need at the moment for an integrated amp like this, but neither of us really wants to see it sold off to an unknown buyer at this point. We'll probably hold on to it for a while until a good need for it turns up.